Billet-specialties Formula - 14" Contrast Cut Instrukcja Użytkownika Pobierz pdf

D-SHAPED STEERING WHEEL

INSTALLATION INSTRUCTIONS

Billet Specialties, Inc. • Tech Line 708-588-0505 • www.billetspecialties.com

BEFORE YOU BEGIN

Remove original steering wheel. Turn wheels to a straight-ahead position. Remove original horn button or center pad

and disconnect horn wire at horn button. Remove horn wire at column by pushing in and turning on the wire post.

Remove the steering shaft nut. Use a steering wheel puller to remove wheel.

1. INSTALL COLUMN ADAPTER

Align horn-post hole on adapter to horn wire connection post on column and slide

adapter on shaft with one of the mounting holes at the 12 o’clock position. Replace

steering shaft nut and hand tighten, do not torque yet.

*Some aftermarket steering columns may not include this piece. This can be purchased

from any GM dealer, AC Delco #26047013

2. INSTALL LEATHER SECTIONS

Carefully place the leather segment into the recessed area. Start the 8-32 flat head screws

in each hole by hand evenly before tightening.

DO NOT OVERTIGHTEN! This will damage the half-wrap.

3. INSTALL STEERING WHEEL

Position steering wheel on adapter and install nine 8-32 flathead screws, tighten down

steering wheel. Check the steering wheel to make sure it is straight. To adjust, remove the

assembly (steering wheel & adapter) and index the adapter on the splined shaft. Once

straight, torque steering shaft nut to 20-25ft. lbs.

Non-Billet Specialties Adapter

Billet Specialties steering wheels are drilled and counter-sunk to work with Billet Specialties

adapters and use 8-32 hardware. Some aftermarket adapters are supplied with 10-32

hardware. On such applications the hardware must be changed to 8-32.

4. INSTALL HORN BUTTON

Install horn wire to post on column by pushing in and twisting to lock it in. The horn wire is

not supplied with some aftermarket columns, but is available as a replacement part from

Billet Specialties - #RP2510.

Attach black ground wire on back of the horn button to the 8-32 tapped hole in adapter

using the supplied 8-32 x 1/4” Phillips screw. Install the spade connector on column horn

wire to center tab on the back of the horn button.

Important: Lube O-ring on horn button and push horn button into bore of adapter.

Adapter

Top View

Steering Column

Adapter

JAN11

Plastic tower goes

thru large hole in

adapter

Pigtail Wire

(Yellow)

Goes thru

large hole

in adapter

Adapter

(Side View)

Adapter

(Top View)

Pigtail Wire

(Yellow)

Goes thru

large hole

in adapter

Horn

Button

Adapter

(Top View)

Podsumowanie treści

Strona 1 - 4. INSTALL HORN BUTTON

D-SHAPED STEERING WHEEL INSTALLATION INSTRUCTIONSBillet Specialties, Inc. • Tech Line 708-588-0505 • www.billetspecialties.comBEFORE YOU BEGINRemove o

Komentarze do niniejszej Instrukcji

Brak uwag

Billet-specialties Formula - 14" Contrast Cut Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Do samochodu Billet-specialties Formula - 14" Contrast Cut. Billet Specialties Formula - 14&quot; Contrast Cut User Manual [en] Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Do samochodu Billet-specialties Formula - 14" Contrast Cut

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Do samochodu Billet-specialties Formula - 14" Contrast Cut. Billet Specialties Formula - 14" Contrast Cut User Manual [en] Instrukcja obsługi